en
EN
BETRIEBSANLEITUNG
HEIZSTRAHLER
AIRGOCLEAN® 140 E / AIRGOCLEAN® 145 E
OPERATING MANUAL
AIR CLEANER
Table of contents
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
Notes regarding the operating manual
Safety
Information about the device
Transport and storage
Assembly and start-up
Operation
AirgoClean® 140 E AirgoClean® 145 E
https://hub.trotec.com/?id=45465
Available accessories
Safety
Errors and faults
Maintenance
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity of the device or its site of use.
Technical annex
Disposal
Notes regarding the operating manual
Symbols
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or moderate injury.
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Read all safety warnings and all instructions.Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.Save all warnings and instructions for future
reference.This appliance can be used by children aged
from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack ofexperience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning anduser maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in aggressive atmosphere.
• Do not operate the device near open fire or gas appliances.
• Only put up the device in an upright, stable position on firm
• ground.
Let the device dry out after a wet clean. Do not operate it when wet.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Do not expose the device to liquids as it is not protected
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
against splash water.
• Never insert any objects or limbs into the device.
• Do not cover the device during operation.
• Do not sit on the device.
• This appliance is not a toy. Keep away from children and
animals. Do not leave the device unattended duringoperation
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Intended use
Use the device for cleaning the air as well as for odour
elimination (ionization) in interior spaces only whilst adhering to the technical data and safety instructions.
Foreseeable misuse
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device out of doors.
• Do not use the device in bathrooms and rooms with a high
humidity level.
• Do not use the device in rooms where large amounts of
dust are produced, e.g. in production halls, workshops or on construction sites.
• Moreover, the integrated filter system is not suited for
removing dusts that are potentially harmful to health (e.g. pollutants) from the air.Any use other than the intended use is regarded as a
reasonably foreseeable misuse. Any unauthorised modifications, alterations or structural changes to the device are forbidden.• Personnel qualifications
People who use this device must:• be aware of the dangers that occur when working with
electrically driven air cleaners. have read and understood the operating manual, especially the Safety chapter.• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any defective devices or device parts.Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Neveruse the device if electric cables or the power connection
are damaged!The mains connection must correspond to the
specifications in the Technical annex.• Insert the mains plug into a properly fused mains socket.
• Observe the technical data when selecting extensions to
the power cable. Completely unroll the extension cable. Avoid electrical overload. Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable. If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!• When positioning the device, observe the minimum
• distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
annex.• Make sure that the air inlet and outlet are not obstructed.
• Make sure that there are no loose items or dirt located in
the immediate surroundings of air inlet and air outlet.• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible condition.
• Do not expose the device to heat or direct sunlight.
• Make sure that the suction side is kept free of dirt and
loose objects.
• Dispose of replaced filters properly, especially after
filtering substances hazardous to health.
• Never use the device as storage place or footstep.
• Do not insert rechargeable batteries into the remote
control.
• Never select automatic mode if the device is used for virus
filtration.
air cleaner AirgoClean® 140 E / AirgoClean® 145 EResidual risks
Information about the device
Work on the electrical components must only be
carried out by an authorised specialist company!
Before any work on the device, remove the mains plug from the mains socket! Do not touch the mains plug with wet or damp hands.Hold onto the mains plug while pulling the power cable
out of the mains socket.
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way! Observe the personnel qualifications!
The device is not a toy and does not belong in the
hands of children.
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Do not operate the device without an air filter inserted
into the air inlet! Without the air filter, the inside of the device will be heavily contaminated. This could reduce the performance and result in damage to the device.
Do not use abrasive cleaners or solvents to clean the
device.
Behaviour in the event of an emergency
• Switch the device off.
2.
In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not reconnect a defective device to the mains.
Device description
The device serves to filter the room air with the aim of reducing
slight and medium contaminations and odours in order to
improve the air quality. It is equipped with a powerful fan sucking in the air. The air flows through the filter and is cleaned. Afterwards the fan releases the clean air back into the room. The 3-in-1 filter is composed of a HEPA filter, a carbon filter and a prefilter. The device uses a HEPA filter to remove bacteria, viruses, pollen, dust mite residue, mould fungus spores and other allergens from the air. The integrated prefilter (made of synthetic fibre) filters out large dust particles before the air flows into the HEPA filter. The integrated carbon filter with activated carbon also removes odours from the air. The HEPA carbon filter is effective against house dust, pet allergens, cigarette smoke, smog and particles which can carry smells and viruses.The device is equipped with an air quality sensor to display the
air quality and control air purification automatically. The device is equipped with an automatic mode, night mode and turbo mode. Additionally, the device comes with an ionization function. The released ions remove pollen, dust, viruses and bacteria from the room air. Thanks to this air purification method, the quality of the room air can be additionally improved. The device comes equipped with a UV function. In combination with the photocatalytic surface of the filter, the UV LED reduces the formation of germs, viruses and odours. The three-stage fan and the uncomplicated, quick filter change ensure easy operation.Thanks to its compact dimensions the device can be
transported conveniently, and owing to its low-noise operation it can be used indoors.The device can be operated via the control panel at the device
or via the infrared remote control. The devices are structurally identical. They merely differ in colour: The device AirgoClean 140 E comes in white colour, the AirgoClean 145 E is black air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Device depiction
Front view
Rear view
Transport and storage
If you store or transport the device improperly, the device may be damaged.Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry handle.
Before transporting the device, observe the following:• Hold onto the mains plug while pulling the power cable out
Switch the device off.
of the mains socket.
• Do not use the power cable to drag the device.
After transporting the device, proceed as follows:• Set up the device in an upright position after transport.
Storage
When the device is not being used, observe the following storage conditions:• dry and protected from frost and heat
in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Remove batteries from the remote control.
No. Designation
Air inlet with HEPA carbon filter and pre-filter
Segment display
Air outlet
Foot
Remote control
Air quality sensor
Transport handle
air cleaner AirgoClean® 140 E / AirgoClean® 145 E1234675
Wall mounting
• Mark the positions for the bore holes on the wall. Observe
the minimum distances specified in the technical data.
• Drill the holes into the wall.
Assembly and start-up
Scope of delivery
1 x device• 1 x HEPA carbon filter incl. pre-filter made of synthetic
• fibre
1 x Foot (large) 2 x Foot (small) 6 x Screw for foot mounting 6 x Screw for wall mounting 1 x Wall holder 6 x Wall plug for wall mounting1 x Remote control
1 x Manual• Unpacking the device
• Open the cardboard box and take the device out.
• Completely remove the packaging.
• Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
Foot assembly
• Fasten both small feet to the large feet using the screws.
• Correctly screw the large feet to the designated points on
the back of the device.
• Check the device for stability
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
3.
Insert appropriate wall plugs into the bore holes depending
on the type of wall. Position the holder on the wall as shown and attach the holder in place with the 6 screws.
Start-up
The HEPA carbon filter is pre-installed.
Remove the plastic cover from the HEPA carbon filter. To insert the HEPA carbon filter, proceed as described under Changing the HEPA carbon filter.
When positioning the device, observe the minimum distancefrom walls or other objects as described in the chapter
Technical annex.
• Hook the device into the holder from above.
• Make sure that the device is attached securely.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition, contact the customer service.
• Only put up the device in an upright, stable position on firm
ground.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.• Make sure that extension cables are completely unrolled.
• Position the device near the source of air contamination.
• When positioning the device, keep a sufficient distance to
heat sources.
• Make sure that no curtains or other objects interfere with
the air flow.
• Make sure that the air inlet and outlet are not obstructed.
Connecting the power cable
• Insert the mains plug into a properly fused mains socket.
air cleaner AirgoClean® 140 E / AirgoClean® 145 EACCD
Operation
Avoid open doors and windows.
Control panel
Remote control
No. Designation
Meaning
PM2.5 colourindicator
PM2.5/Timerindication
10 %RH indicationSpeed LEDs
On/Off button
Timer button
Locked button
Auto button
Ionizer button
Filter button
UV button
Speed button
Sleep button
Temperature
indication
Timer
Bar illumination changes colour =automatic mode
Illuminated in different colours
according to the measured air
quality:• green = good
yellow = medium red = poor
Indication of the fine dust pollution
in µg/m3 or the number of hours of the set timer (1 h – 24 h)
Indication of the relative humidity
level
Are illuminated according to the
set fan stage and air quality:• 1 bar = low
2 bars = medium 3 bars = high (turbo mode)
Switching the device on and off
Switching on the timer function: 1 h – 24 h
Switching the locking function on
and off
Switching the automatic mode on
or off
Switching the ionization mode on
or off
Press the button to perform the
filter reset
Switching the UV function on andoff
Setting the fan speed
Switching night mode on or off
Indication of the current
temperature in °C
Increasing the number of hours of
the timer
Reducing the number of hours of
the timer
Speed
Reducing the fan speed
Increasing the fan speed
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Switching the device on
Once you have completely installed the device as described in
the chapter Assembly and start-up, you can switch it on.• Press the On/Off button (12) to switch the device on.
Please proceed as follows to switch off the automatic mode:• Press the Auto button (15).
The illumination of the Auto button (15) goes out. The device switches to ventilation mode.
Info
Automatic mode and virus filtration
Do not use the automatic mode if the device is used for
virus filtration!The integrated sensors only respond to air pollution
caused by fine particulates, pollen or possibly VOC (organic chemical compounds). The device cannot determine the virus load inside the room. It is possiblethat the automatic mode indicates a good air quality
even though the virus load in the room is very high. Therefore, when using the device for virus filtration, werecommend that you always select a fixed performance
level adapted to the room size or the required
circulation rate.
Night mode
In night mode, the control panel is dimmed and the devicegenerates a gentle air current that is adapted to your sleep
habits. Proceed as follows to switch on night mode:• Press the Sleep button (20).
The Sleep button (20) is illuminated.
• Press the Sleep button (20) again to switch off the night
mode. The illumination of the Sleep button (20) goes out. The device operates at fan speed 1 and the automatic mode is activated.
Ventilation
In ventilation mode, you can select all fan speeds manually. Please proceed as follows to select the fan stages:• Select the desired speed by pressing the Speed button (19)
repeatedly until the desired fan stage is reached. The Speed button (19) is illuminated. The
Speed LEDs (11) are illuminated according to the selected fan stage.
The device emits an acoustic signal. The device measures the air quality within 3 minutes. The PM2.5 colour indicator (8) shows the respective colour for the current air quality. The Auto button (15) is illuminated. The Speed LEDs (11) are illuminated according to the
measured air quality and fan stage.
Setting the operating mode
The device comes with the following operating modes:• Night mode
Ventilation
• Automatic mode
Automatic mode
When in automatic mode, the device automatically detects the air quality. Please proceed as follows to set the automatic mode:• Press the Auto button (15).
The Auto button (15) is illuminated. The device is running in automatic mode. The device measures the air quality within 3 minutes. The PM2.5 colour indicator (8) shows the respective colour for the current air quality.
If the device is in automatic mode while it is getting dark, thelight detection function will automatically put the device into
night mode. Once the ambient brightness increases, the device switches back to automatic mode. The PM2.5/Timer indication (9) shows the measured fine dust pollution (PM2.5 value). The Speed LEDs (11) are illuminated according to the automatically selected fan stage. Depending on the measured fine dust pollution, the air quality is shown via the PM2.5 colour indicator (8) and the PM2.5/ Timer indication (9) as follows:
Air quality colour indicator
Fine dust value
indication (PM2.5 value)
Illuminated in green
(very good air quality)
Illuminated in yellow
(medium air quality)
Illuminated in red
(poor air quality)
0–50
51-100
> 100
air cleaner AirgoClean® 140 E / AirgoClean® 145 ESwitching the locking function on and off
The locking function prevents the buttons on the control panel
from being used. Please proceed as follows to lock the control panel:• Press the Locked button (14) for 3 seconds.
The Locked button (14) is illuminated. The locking function is activated. The buttons on the control panel cannot be used.
• Press the Locked button (14) for 3 seconds again to switch
off the function.
Ionization
The ionization function serves to filter out pollen, dust, virusesand bacteria from the room air by means of the HEPA carbon
filter with integrated pre-filter. If the ionization function is activated, automatic mode is added automatically. Please proceed as follows to activate the ionization function:• Press the ionizer button (16) to switch on the ionization
function. The Ionizer button (16) is illuminated. The device automatically starts in automatic mode. The
Auto button (15) is illuminated.
The device starts to filter the room air.• Select the desired fan speed by pressing the
Speed button (19).Automatic mode is deactivated automatically and the
illumination of the Auto button (15) goes out.
The Speed button (19) is illuminated. The
Speed LEDs (11) are illuminated according to the selected fan stage.
• Press the ionizer button (16) again to deactivate the
ionization function. The illumination of the Ionizer button (16) goes out.
UV function In combination with the photocatalytic surface of the filter, the UV LED reduces the formation of germs, viruses and odours. Please proceed as follows to switch on the UV function:• Press the UV button (18) to switch on the UV function.
The UV button (18) is illuminated.
• Press the UV button (18) again to deactivate the
UV function. The illumination of the UV button (18) goes out.
Setting the timer
The function can be set in all operating modes. The number of hours can be set from 1 h to 24 h.
Automatic switch-off
• Press the Timer button (13) until the desired number of
hours has been set. The Timer button (13) is illuminated. The PM2.5/Timer indication (9) shows the set number of hours of the timer. In night mode, the set number of hours is not displayed, but the night mode button (20) appears dimmed on the segment display.
The timer programming is activated.The device switches off automatically after the set
number of hours has elapsed. Notes regarding automatic switch-off:• Pressing the On/Off button (12) deactivates the automatic
switch-off function.
Shutdown
Do not touch the mains plug with wet or damp hands.
Press the On/Off button (12).• Hold onto the mains plug while pulling the power cable out
• of the mains socket.
Clean the device according to the Maintenance chapter.Store the device according to the Transport and storage
chapter.
Available accessories
Only use accessories and additional equipment
specified in the operating manual.Using insertion tools or accessories other than those
specified in the operating manual may cause a risk of
injury.
Designation
HEPA filters
HEPA carbon filter
HEPA filter (99.97 %)
HEPA carbon filter (99.97 %)
Article number
7.160.000.526
7.160.000.527
7.160.000.528
7.160.000.529 air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless, check the device according to the following list.
• The device gives off an unpleasant odour:
• Check the HEPA carbon filter (27) for dirt. If necessary,
replace the HEPA carbon filter. Smoke, e.g. dense tobacco smoke, odours and contaminations may be in the air. Ventilate the room.
The device still does not operate correctly after these
checks: Please contact the customer service. If necessary, bring thedevice to an authorised specialist electrical company or to
Trotec for repair.
Check the power connection. Check the power cable and mains plug for damage. Check the on-site fusing.
The device does not start:• Wait for 10 minutes before restarting the device. If the
device is not starting, have the electrics checked by a specialist company or by Trotec.
The device is loud or vibrates:• Check whether the device is set up in a stable and upright
position.
The device gets very warm, is loud or is losing performance:• Check the air inlets and air filters for dirt. Remove external
dirt.
The device works with reduced capacity:• Check the HEPA carbon filter (27) for dirt. If necessary,
replace the HEPA carbon filter. The HEPA carbon filter (27) is soiled and has to be cleaned. Clean the HEPA carbon filter (see chapter Operation and maintenance). The air outlet is obstructed. Make sure that the air outlet is not blocked. If applicable, remove loose objects from the air outlet. The HEPA carbon filter's plastic cover was not removed before installation. Take the HEPA carbon filter out of the plastic cover. The air quality sensor is clogged or soiled. Windows and doors should be closed, otherwise dust and other contamination is able to enter the room. Clean the air quality sensor as described in the Maintenance chapter.
The device works with no capacity or the air quality does
not improve:• Check whether any windows and/or doors of the room are
open. If so, close them. The HEPA carbon filter is not installed. Install the HEPA carbon filter. Check the minimum distance to walls or other objects. Position the device a little more in the room's centre if required.• air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Maintenance
Maintenance and care interval
Check air inlets and outlets for dirt
and foreign objects and clean
if necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the filter for dirt and foreign
objects and clean or replace if
necessary
Replace the HEPA carbon filter
Check for damage
Check the attachment screws
Test run
Maintenance intervals
before every
start-up
as needed
at least every
2 weeks
at least every
4 weeks
at least every
6 months
at least
annually
Maintenance and care log
Device type:
Device number
Maintenance and care interval
Check air inlets and outlets for dirt
and foreign objects and clean
if necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the filter for dirt and foreign
objects and clean or replace if
necessary
Replace the HEPA carbon filter
Check for damage
Check the attachment screws
Test run
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Activities required before starting maintenance
Cleaning and replacing the HEPA carbon filter
Do not operate the device without the HEPA carbon
filters inserted!
The HEPA carbon filter cannot be washed and must be
replaced if necessary.
The lifetime of the HEPA carbon filter depends on the
ambient conditions and the application period of the
device.
• The HEPA carbon filter must be cleaned or replaced if it is
very dirty. This is brought to light e.g. by a reduced capacity (see chapter Errors and faults).
• Make sure that the HEPA carbon filter is installed before
switching the device on.
• Without the HEPA carbon filter, the device cannot fulfil its
air cleaner function, and the inside of the device will be soiled.
The HEPA carbon filter must be cleaned as soon as it is dirty.The HEPA carbon filter must be replaced in case of heavy
soiling. If the Filter button (17) is illuminated, the HEPA carbon filter must also be replaced.Visually inspect the HEPA carbon filter for dirt before each
start-up.
Do not touch the mains plug with wet or damp hands.
Switch the device off.• Hold onto the mains plug while pulling the power cable out
of the mains socket.
Tasks which require the device to be opened must
only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Make sure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
Clean the air outlet if required.Carefully clean the air outlet from the outside with a
soft, damp and lint-free cloth.
Clean the air quality sensor if required. Carefully clean it from the outside with a soft, damp and lint-free cloth.
Visual inspection of the inside of the device for dirt
• Remove the air filters.
• Use a torch to illuminate the openings of the device.
• Check the inside of the device for dirt.
4.
If you see a thick layer of dust, clean the inside of the device with a vacuum cleaner.
• Reinsert the air filters.
air cleaner AirgoClean® 140 E / AirgoClean® 145 E Please proceed as follows: ü The device is switched off.• Fold out the device cover (26) towards the front.
4.
Insert the cleaned / new HEPA carbon filter (27) into the device. Make sure that the strips (28) are positioned as indicated.
• Pull the strips (28) to take the HEPA carbon filter (27) out of
the device.
• Close the device cover (26) again.
• Clean the HEPA carbon filter (27) with a dry, lint-free cloth
if it is slightly dirty. If heavily soiled, dispose of the HEPA carbon filter (27) in accordance with the nationalregulations and remove the new HEPA carbon filter from
the plastic cover.
• Press the Filter button (17)for 3 seconds to perform the
filter reset. The illumination of the Filter button (17) goes out air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Cleaning the air quality sensor
The air quality sensor(6) has to be cleaned every 3 months or once it is soiled (please also refer to the Chapter Operation and Chapter Errors and faults).• Clean the sensor cover using a soft, lint-free cloth.
• Open the sensor cover by sliding the cover towards the
side.
• Carefully clean the sensor lens (29) with a cotton bud
slightly moistened with water. Do not use too much water as this could damage the sensor.
• Carefully dry the lens with a dry cotton bud.
• Then close the sensor cover again.
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Technical annex
Technical data
Parameter
Model
Value
AirgoClean® 140 E (white) AirgoClean® 145 E (black)
Air flow rate with HEPA
carbon filter
Fan stage I
Fan stage II
Fan stage III (turbo mode)
130 m3/h 240 m3/h 330 m3/h
Ambient temperature
0 °C to 35 °C
Operating range
0 % to 90 % RH
Mains connection
220-240 V / 50-60 Hz
Power input
Nominal current
85 W
0.37 A
Sound pressure level (at a distance of 1 m) Stage 1 (night mode) Stage 2 Stage 3 (turbo mode)
Dimensions incl. foot (length x width x height)
Minimum distance to walls
and other objects
34.5 dB(A) 43 dB(A) 50 dB(A)
A: top C: side D: front
30 cm 30 cm 30 cm
7.5 kg
Weight
Remote control batteries
3V CR2032
Disposal
The icon with the crossed-out waste bin on waste
EN
BETRIEBSANLEITUNG
HEIZSTRAHLER
AIRGOCLEAN® 140 E / AIRGOCLEAN® 145 E
OPERATING MANUAL
AIR CLEANER
Table of contents
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
Notes regarding the operating manual
Safety
Information about the device
Transport and storage
Assembly and start-up
Operation
AirgoClean® 140 E AirgoClean® 145 E
https://hub.trotec.com/?id=45465
Available accessories
Safety
Errors and faults
Maintenance
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity of the device or its site of use.
Technical annex
Disposal
Notes regarding the operating manual
Symbols
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or moderate injury.
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Read all safety warnings and all instructions.Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.Save all warnings and instructions for future
reference.This appliance can be used by children aged
from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack ofexperience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning anduser maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in aggressive atmosphere.
• Do not operate the device near open fire or gas appliances.
• Only put up the device in an upright, stable position on firm
• ground.
Let the device dry out after a wet clean. Do not operate it when wet.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Do not expose the device to liquids as it is not protected
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
against splash water.
• Never insert any objects or limbs into the device.
• Do not cover the device during operation.
• Do not sit on the device.
• This appliance is not a toy. Keep away from children and
animals. Do not leave the device unattended duringoperation
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Intended use
Use the device for cleaning the air as well as for odour
elimination (ionization) in interior spaces only whilst adhering to the technical data and safety instructions.
Foreseeable misuse
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device out of doors.
• Do not use the device in bathrooms and rooms with a high
humidity level.
• Do not use the device in rooms where large amounts of
dust are produced, e.g. in production halls, workshops or on construction sites.
• Moreover, the integrated filter system is not suited for
removing dusts that are potentially harmful to health (e.g. pollutants) from the air.Any use other than the intended use is regarded as a
reasonably foreseeable misuse. Any unauthorised modifications, alterations or structural changes to the device are forbidden.• Personnel qualifications
People who use this device must:• be aware of the dangers that occur when working with
electrically driven air cleaners. have read and understood the operating manual, especially the Safety chapter.• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any defective devices or device parts.Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Neveruse the device if electric cables or the power connection
are damaged!The mains connection must correspond to the
specifications in the Technical annex.• Insert the mains plug into a properly fused mains socket.
• Observe the technical data when selecting extensions to
the power cable. Completely unroll the extension cable. Avoid electrical overload. Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable. If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!• When positioning the device, observe the minimum
• distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
annex.• Make sure that the air inlet and outlet are not obstructed.
• Make sure that there are no loose items or dirt located in
the immediate surroundings of air inlet and air outlet.• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible condition.
• Do not expose the device to heat or direct sunlight.
• Make sure that the suction side is kept free of dirt and
loose objects.
• Dispose of replaced filters properly, especially after
filtering substances hazardous to health.
• Never use the device as storage place or footstep.
• Do not insert rechargeable batteries into the remote
control.
• Never select automatic mode if the device is used for virus
filtration.
air cleaner AirgoClean® 140 E / AirgoClean® 145 EResidual risks
Information about the device
Work on the electrical components must only be
carried out by an authorised specialist company!
Before any work on the device, remove the mains plug from the mains socket! Do not touch the mains plug with wet or damp hands.Hold onto the mains plug while pulling the power cable
out of the mains socket.
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way! Observe the personnel qualifications!
The device is not a toy and does not belong in the
hands of children.
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Do not operate the device without an air filter inserted
into the air inlet! Without the air filter, the inside of the device will be heavily contaminated. This could reduce the performance and result in damage to the device.
Do not use abrasive cleaners or solvents to clean the
device.
Behaviour in the event of an emergency
• Switch the device off.
2.
In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not reconnect a defective device to the mains.
Device description
The device serves to filter the room air with the aim of reducing
slight and medium contaminations and odours in order to
improve the air quality. It is equipped with a powerful fan sucking in the air. The air flows through the filter and is cleaned. Afterwards the fan releases the clean air back into the room. The 3-in-1 filter is composed of a HEPA filter, a carbon filter and a prefilter. The device uses a HEPA filter to remove bacteria, viruses, pollen, dust mite residue, mould fungus spores and other allergens from the air. The integrated prefilter (made of synthetic fibre) filters out large dust particles before the air flows into the HEPA filter. The integrated carbon filter with activated carbon also removes odours from the air. The HEPA carbon filter is effective against house dust, pet allergens, cigarette smoke, smog and particles which can carry smells and viruses.The device is equipped with an air quality sensor to display the
air quality and control air purification automatically. The device is equipped with an automatic mode, night mode and turbo mode. Additionally, the device comes with an ionization function. The released ions remove pollen, dust, viruses and bacteria from the room air. Thanks to this air purification method, the quality of the room air can be additionally improved. The device comes equipped with a UV function. In combination with the photocatalytic surface of the filter, the UV LED reduces the formation of germs, viruses and odours. The three-stage fan and the uncomplicated, quick filter change ensure easy operation.Thanks to its compact dimensions the device can be
transported conveniently, and owing to its low-noise operation it can be used indoors.The device can be operated via the control panel at the device
or via the infrared remote control. The devices are structurally identical. They merely differ in colour: The device AirgoClean 140 E comes in white colour, the AirgoClean 145 E is black air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Device depiction
Front view
Rear view
Transport and storage
If you store or transport the device improperly, the device may be damaged.Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry handle.
Before transporting the device, observe the following:• Hold onto the mains plug while pulling the power cable out
Switch the device off.
of the mains socket.
• Do not use the power cable to drag the device.
After transporting the device, proceed as follows:• Set up the device in an upright position after transport.
Storage
When the device is not being used, observe the following storage conditions:• dry and protected from frost and heat
in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Remove batteries from the remote control.
No. Designation
Air inlet with HEPA carbon filter and pre-filter
Segment display
Air outlet
Foot
Remote control
Air quality sensor
Transport handle
air cleaner AirgoClean® 140 E / AirgoClean® 145 E1234675
Wall mounting
• Mark the positions for the bore holes on the wall. Observe
the minimum distances specified in the technical data.
• Drill the holes into the wall.
Assembly and start-up
Scope of delivery
1 x device• 1 x HEPA carbon filter incl. pre-filter made of synthetic
• fibre
1 x Foot (large) 2 x Foot (small) 6 x Screw for foot mounting 6 x Screw for wall mounting 1 x Wall holder 6 x Wall plug for wall mounting1 x Remote control
1 x Manual• Unpacking the device
• Open the cardboard box and take the device out.
• Completely remove the packaging.
• Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
Foot assembly
• Fasten both small feet to the large feet using the screws.
• Correctly screw the large feet to the designated points on
the back of the device.
• Check the device for stability
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
3.
Insert appropriate wall plugs into the bore holes depending
on the type of wall. Position the holder on the wall as shown and attach the holder in place with the 6 screws.
Start-up
The HEPA carbon filter is pre-installed.
Remove the plastic cover from the HEPA carbon filter. To insert the HEPA carbon filter, proceed as described under Changing the HEPA carbon filter.
When positioning the device, observe the minimum distancefrom walls or other objects as described in the chapter
Technical annex.
• Hook the device into the holder from above.
• Make sure that the device is attached securely.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition, contact the customer service.
• Only put up the device in an upright, stable position on firm
ground.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.• Make sure that extension cables are completely unrolled.
• Position the device near the source of air contamination.
• When positioning the device, keep a sufficient distance to
heat sources.
• Make sure that no curtains or other objects interfere with
the air flow.
• Make sure that the air inlet and outlet are not obstructed.
Connecting the power cable
• Insert the mains plug into a properly fused mains socket.
air cleaner AirgoClean® 140 E / AirgoClean® 145 EACCD
Operation
Avoid open doors and windows.
Control panel
Remote control
No. Designation
Meaning
PM2.5 colourindicator
PM2.5/Timerindication
10 %RH indicationSpeed LEDs
On/Off button
Timer button
Locked button
Auto button
Ionizer button
Filter button
UV button
Speed button
Sleep button
Temperature
indication
Timer
Bar illumination changes colour =automatic mode
Illuminated in different colours
according to the measured air
quality:• green = good
yellow = medium red = poor
Indication of the fine dust pollution
in µg/m3 or the number of hours of the set timer (1 h – 24 h)
Indication of the relative humidity
level
Are illuminated according to the
set fan stage and air quality:• 1 bar = low
2 bars = medium 3 bars = high (turbo mode)
Switching the device on and off
Switching on the timer function: 1 h – 24 h
Switching the locking function on
and off
Switching the automatic mode on
or off
Switching the ionization mode on
or off
Press the button to perform the
filter reset
Switching the UV function on andoff
Setting the fan speed
Switching night mode on or off
Indication of the current
temperature in °C
Increasing the number of hours of
the timer
Reducing the number of hours of
the timer
Speed
Reducing the fan speed
Increasing the fan speed
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Switching the device on
Once you have completely installed the device as described in
the chapter Assembly and start-up, you can switch it on.• Press the On/Off button (12) to switch the device on.
Please proceed as follows to switch off the automatic mode:• Press the Auto button (15).
The illumination of the Auto button (15) goes out. The device switches to ventilation mode.
Info
Automatic mode and virus filtration
Do not use the automatic mode if the device is used for
virus filtration!The integrated sensors only respond to air pollution
caused by fine particulates, pollen or possibly VOC (organic chemical compounds). The device cannot determine the virus load inside the room. It is possiblethat the automatic mode indicates a good air quality
even though the virus load in the room is very high. Therefore, when using the device for virus filtration, werecommend that you always select a fixed performance
level adapted to the room size or the required
circulation rate.
Night mode
In night mode, the control panel is dimmed and the devicegenerates a gentle air current that is adapted to your sleep
habits. Proceed as follows to switch on night mode:• Press the Sleep button (20).
The Sleep button (20) is illuminated.
• Press the Sleep button (20) again to switch off the night
mode. The illumination of the Sleep button (20) goes out. The device operates at fan speed 1 and the automatic mode is activated.
Ventilation
In ventilation mode, you can select all fan speeds manually. Please proceed as follows to select the fan stages:• Select the desired speed by pressing the Speed button (19)
repeatedly until the desired fan stage is reached. The Speed button (19) is illuminated. The
Speed LEDs (11) are illuminated according to the selected fan stage.
The device emits an acoustic signal. The device measures the air quality within 3 minutes. The PM2.5 colour indicator (8) shows the respective colour for the current air quality. The Auto button (15) is illuminated. The Speed LEDs (11) are illuminated according to the
measured air quality and fan stage.
Setting the operating mode
The device comes with the following operating modes:• Night mode
Ventilation
• Automatic mode
Automatic mode
When in automatic mode, the device automatically detects the air quality. Please proceed as follows to set the automatic mode:• Press the Auto button (15).
The Auto button (15) is illuminated. The device is running in automatic mode. The device measures the air quality within 3 minutes. The PM2.5 colour indicator (8) shows the respective colour for the current air quality.
If the device is in automatic mode while it is getting dark, thelight detection function will automatically put the device into
night mode. Once the ambient brightness increases, the device switches back to automatic mode. The PM2.5/Timer indication (9) shows the measured fine dust pollution (PM2.5 value). The Speed LEDs (11) are illuminated according to the automatically selected fan stage. Depending on the measured fine dust pollution, the air quality is shown via the PM2.5 colour indicator (8) and the PM2.5/ Timer indication (9) as follows:
Air quality colour indicator
Fine dust value
indication (PM2.5 value)
Illuminated in green
(very good air quality)
Illuminated in yellow
(medium air quality)
Illuminated in red
(poor air quality)
0–50
51-100
> 100
air cleaner AirgoClean® 140 E / AirgoClean® 145 ESwitching the locking function on and off
The locking function prevents the buttons on the control panel
from being used. Please proceed as follows to lock the control panel:• Press the Locked button (14) for 3 seconds.
The Locked button (14) is illuminated. The locking function is activated. The buttons on the control panel cannot be used.
• Press the Locked button (14) for 3 seconds again to switch
off the function.
Ionization
The ionization function serves to filter out pollen, dust, virusesand bacteria from the room air by means of the HEPA carbon
filter with integrated pre-filter. If the ionization function is activated, automatic mode is added automatically. Please proceed as follows to activate the ionization function:• Press the ionizer button (16) to switch on the ionization
function. The Ionizer button (16) is illuminated. The device automatically starts in automatic mode. The
Auto button (15) is illuminated.
The device starts to filter the room air.• Select the desired fan speed by pressing the
Speed button (19).Automatic mode is deactivated automatically and the
illumination of the Auto button (15) goes out.
The Speed button (19) is illuminated. The
Speed LEDs (11) are illuminated according to the selected fan stage.
• Press the ionizer button (16) again to deactivate the
ionization function. The illumination of the Ionizer button (16) goes out.
UV function In combination with the photocatalytic surface of the filter, the UV LED reduces the formation of germs, viruses and odours. Please proceed as follows to switch on the UV function:• Press the UV button (18) to switch on the UV function.
The UV button (18) is illuminated.
• Press the UV button (18) again to deactivate the
UV function. The illumination of the UV button (18) goes out.
Setting the timer
The function can be set in all operating modes. The number of hours can be set from 1 h to 24 h.
Automatic switch-off
• Press the Timer button (13) until the desired number of
hours has been set. The Timer button (13) is illuminated. The PM2.5/Timer indication (9) shows the set number of hours of the timer. In night mode, the set number of hours is not displayed, but the night mode button (20) appears dimmed on the segment display.
The timer programming is activated.The device switches off automatically after the set
number of hours has elapsed. Notes regarding automatic switch-off:• Pressing the On/Off button (12) deactivates the automatic
switch-off function.
Shutdown
Do not touch the mains plug with wet or damp hands.
Press the On/Off button (12).• Hold onto the mains plug while pulling the power cable out
• of the mains socket.
Clean the device according to the Maintenance chapter.Store the device according to the Transport and storage
chapter.
Available accessories
Only use accessories and additional equipment
specified in the operating manual.Using insertion tools or accessories other than those
specified in the operating manual may cause a risk of
injury.
Designation
HEPA filters
HEPA carbon filter
HEPA filter (99.97 %)
HEPA carbon filter (99.97 %)
Article number
7.160.000.526
7.160.000.527
7.160.000.528
7.160.000.529 air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless, check the device according to the following list.
• The device gives off an unpleasant odour:
• Check the HEPA carbon filter (27) for dirt. If necessary,
replace the HEPA carbon filter. Smoke, e.g. dense tobacco smoke, odours and contaminations may be in the air. Ventilate the room.
The device still does not operate correctly after these
checks: Please contact the customer service. If necessary, bring thedevice to an authorised specialist electrical company or to
Trotec for repair.
Check the power connection. Check the power cable and mains plug for damage. Check the on-site fusing.
The device does not start:• Wait for 10 minutes before restarting the device. If the
device is not starting, have the electrics checked by a specialist company or by Trotec.
The device is loud or vibrates:• Check whether the device is set up in a stable and upright
position.
The device gets very warm, is loud or is losing performance:• Check the air inlets and air filters for dirt. Remove external
dirt.
The device works with reduced capacity:• Check the HEPA carbon filter (27) for dirt. If necessary,
replace the HEPA carbon filter. The HEPA carbon filter (27) is soiled and has to be cleaned. Clean the HEPA carbon filter (see chapter Operation and maintenance). The air outlet is obstructed. Make sure that the air outlet is not blocked. If applicable, remove loose objects from the air outlet. The HEPA carbon filter's plastic cover was not removed before installation. Take the HEPA carbon filter out of the plastic cover. The air quality sensor is clogged or soiled. Windows and doors should be closed, otherwise dust and other contamination is able to enter the room. Clean the air quality sensor as described in the Maintenance chapter.
The device works with no capacity or the air quality does
not improve:• Check whether any windows and/or doors of the room are
open. If so, close them. The HEPA carbon filter is not installed. Install the HEPA carbon filter. Check the minimum distance to walls or other objects. Position the device a little more in the room's centre if required.• air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Maintenance
Maintenance and care interval
Check air inlets and outlets for dirt
and foreign objects and clean
if necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the filter for dirt and foreign
objects and clean or replace if
necessary
Replace the HEPA carbon filter
Check for damage
Check the attachment screws
Test run
Maintenance intervals
before every
start-up
as needed
at least every
2 weeks
at least every
4 weeks
at least every
6 months
at least
annually
Maintenance and care log
Device type:
Device number
Maintenance and care interval
Check air inlets and outlets for dirt
and foreign objects and clean
if necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the filter for dirt and foreign
objects and clean or replace if
necessary
Replace the HEPA carbon filter
Check for damage
Check the attachment screws
Test run
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature:
• Date:
Signature
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Activities required before starting maintenance
Cleaning and replacing the HEPA carbon filter
Do not operate the device without the HEPA carbon
filters inserted!
The HEPA carbon filter cannot be washed and must be
replaced if necessary.
The lifetime of the HEPA carbon filter depends on the
ambient conditions and the application period of the
device.
• The HEPA carbon filter must be cleaned or replaced if it is
very dirty. This is brought to light e.g. by a reduced capacity (see chapter Errors and faults).
• Make sure that the HEPA carbon filter is installed before
switching the device on.
• Without the HEPA carbon filter, the device cannot fulfil its
air cleaner function, and the inside of the device will be soiled.
The HEPA carbon filter must be cleaned as soon as it is dirty.The HEPA carbon filter must be replaced in case of heavy
soiling. If the Filter button (17) is illuminated, the HEPA carbon filter must also be replaced.Visually inspect the HEPA carbon filter for dirt before each
start-up.
Do not touch the mains plug with wet or damp hands.
Switch the device off.• Hold onto the mains plug while pulling the power cable out
of the mains socket.
Tasks which require the device to be opened must
only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Make sure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
Clean the air outlet if required.Carefully clean the air outlet from the outside with a
soft, damp and lint-free cloth.
Clean the air quality sensor if required. Carefully clean it from the outside with a soft, damp and lint-free cloth.
Visual inspection of the inside of the device for dirt
• Remove the air filters.
• Use a torch to illuminate the openings of the device.
• Check the inside of the device for dirt.
4.
If you see a thick layer of dust, clean the inside of the device with a vacuum cleaner.
• Reinsert the air filters.
air cleaner AirgoClean® 140 E / AirgoClean® 145 E Please proceed as follows: ü The device is switched off.• Fold out the device cover (26) towards the front.
4.
Insert the cleaned / new HEPA carbon filter (27) into the device. Make sure that the strips (28) are positioned as indicated.
• Pull the strips (28) to take the HEPA carbon filter (27) out of
the device.
• Close the device cover (26) again.
• Clean the HEPA carbon filter (27) with a dry, lint-free cloth
if it is slightly dirty. If heavily soiled, dispose of the HEPA carbon filter (27) in accordance with the nationalregulations and remove the new HEPA carbon filter from
the plastic cover.
• Press the Filter button (17)for 3 seconds to perform the
filter reset. The illumination of the Filter button (17) goes out air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Cleaning the air quality sensor
The air quality sensor(6) has to be cleaned every 3 months or once it is soiled (please also refer to the Chapter Operation and Chapter Errors and faults).• Clean the sensor cover using a soft, lint-free cloth.
• Open the sensor cover by sliding the cover towards the
side.
• Carefully clean the sensor lens (29) with a cotton bud
slightly moistened with water. Do not use too much water as this could damage the sensor.
• Carefully dry the lens with a dry cotton bud.
• Then close the sensor cover again.
air cleaner AirgoClean® 140 E / AirgoClean® 145 E
Technical annex
Technical data
Parameter
Model
Value
AirgoClean® 140 E (white) AirgoClean® 145 E (black)
Air flow rate with HEPA
carbon filter
Fan stage I
Fan stage II
Fan stage III (turbo mode)
130 m3/h 240 m3/h 330 m3/h
Ambient temperature
0 °C to 35 °C
Operating range
0 % to 90 % RH
Mains connection
220-240 V / 50-60 Hz
Power input
Nominal current
85 W
0.37 A
Sound pressure level (at a distance of 1 m) Stage 1 (night mode) Stage 2 Stage 3 (turbo mode)
Dimensions incl. foot (length x width x height)
Minimum distance to walls
and other objects
34.5 dB(A) 43 dB(A) 50 dB(A)
A: top C: side D: front
30 cm 30 cm 30 cm
7.5 kg
Weight
Remote control batteries
3V CR2032
Disposal
The icon with the crossed-out waste bin on waste