TCH 18 E / TCH 19 E
BETRIEBSANLEITUNG
HEIZSTRAHLER
INSTRUCTIONS
CONVECTOR
EN This product is only suitable for well
insulated spaces or occasional use.
Table of contents
You can download the current version of these instructions via
the following link:
Information on the use of these instructions
Safety
Information about the device
Transport and storage
Assembly and start-up
Operation
Errors and faults
https://hub.trotec.com/?id=42756
Maintenance
Technical annex
Disposal
Information on the use of these instructions
Safety
https://hub.trotec.com/?id=42757
Symbols
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or moderate injury.
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity of the device or its site of use.
Read all safety warnings and all instructions.Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.Save all warnings and instructions for future
reference.This appliance can be used by children aged from
8 years and above and persons with reduced physical,sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance. Cleaning anduser maintenance shall not be done by children without
supervision.
Children of less than 3 years should be kept away from the device unless continuously supervised. Children aged from 3 years and less than 8 years shallonly switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance orperform user maintenance
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in an aggressive atmosphere.
• Place the device in an upright and stable position on a
horizontal and stable surface. Let the device dry out after a wet clean. Do not operate it when wet.• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover the device during operation.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible condition.
• Do not sit on the device.
• This appliance is not a toy. Keep away from children and
animals.Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any defective devices or device parts.Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Neveruse the device if electric cables or the power connection
are damaged!The mains connection must correspond to the
specifications in the Technical annex. Insert the mains plug into a properly fused mains socket.• Observe the device's power input, cable length and
• intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical overload. Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by aspecial cord or assembly available from the manufacturer
or its service agent. Defective power cables pose a serious health risk!The power cable must not rest on the device or run in front
of the air outlet, otherwise it may be damaged as a result of high temperatures.• When installing the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions according to the technical
data (chapter Technical annex).
• Do not mount the device to a wall and operate it there.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that the suction side is kept free of dirt and
loose objects.
• Do not place the device on combustible ground.
• Only use original spare parts, for otherwise safe and
• functional operation cannot be ensured.
Allow the device to cool down before transport and/or
maintenance work.The device must not be positioned directly beneath a wall
socket.The device must be set up in a way that the switches and
controllers cannot be touched by a person in a bathtub or
shower.
• Do not use the device if it has been dropped or if it shows
• visible signs of damage.
Keep the safety distance specified in the technical data
between the air inlet and the air outlet of the device and all
combustible materials such as textiles, curtains, beds and sofas, but at least 1 m.
Intended use
The device is only suitable for well insulated spaces or
occasional use. The device is suitable for heating in closed rooms. It has beenspecially developed for private use and is not intended for
commercial use. It is particularly practical to provide additional heating. The device is designed exclusively for installation on the floor. Any use other than the intended use is regarded as misuse.
Reasonably foreseeable misuse
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
• Do not use outdoors.
• Do not use the device for heating vehicles.
• Never immerse the device in water.
• The device must not be mounted to and operated on a
wall.
• Do not make any unauthorised modifications, alterations or
structural changes to the device.
• Do not use the heating device in immediate vicinity of
swimming pools, bathtubs and showers.
Personnel qualification
People who use this device must:• be aware of the dangers that occur when working with
electric devices in damp areas. have read and understood the instructions, especially the Safety chapter.
• Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
the manufacturer.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates that it
is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device. In order to avoid overheating and fire hazards, the heater must not be covered.
Residual risks
Work on the electrical components must only be
carried out by an authorised specialist company!
Before any work on the device, remove the mains plug from the mains socket! Do not touch the mains plug with wet or damp hands.Hold onto the mains plug while pulling the power cable
out of the mains socket.
Risk of electric shock! The device is not protected against water. There is a risk of electric shock! Never use the device in areas where dripping, spraying or running water can enter the device! Never immerse the device in water!
Warning of hot surface
Parts of this appliance can become very hot and cause
burns. Particular attention is to be paid when there are children or vulnerable persons present!
Improper handling entails a risk of burning and electric
shock. Only use the device as intended!
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way! Observe the personnel qualifications!
The device is not a toy and does not belong in the
hands of children.
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Improper installation entails a risk of fire. Do not place the device on combustible ground. Do not place the device on high-pile carpets.
In order to avoid overheating and fire hazards, the device must not be covered!
Behaviour in the event of an emergency
• Switch the device off.
• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to
• Do not reconnect a defective device to the mains.
Overheating protection
The device is provided with a safety thermostat which is
activated by overheating of the device:• In such an event the device switches off automatically.
The lamps at the flip switches for the power stages turn
off.
When the safety thermostat is activated, allow the device to cool down. Only then start to look for the cause of overheating. Should the problem persist, please contact the customer service.
Information about the device
Device description
The convectors TCH 18 E / TCH 19 E serve to generate warm air in interior spaces.The device generates heat by means of an electric heating
element. The air surrounding the heating element is heated. The heated air rises through the air outlet and thus enters the room.The device is equipped with an integrated thermostat and so
generates a constant flow of warm air. The device is not protected against water (IP20)
Device depiction
No. Designation
Air outlet
Control panel
Foot
Carrying handle
Air inlet
Transport and storage
If you store or transport the device improperly, the device may be damaged.Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry handle.
Switch the device off.
Before transporting the device, observe the following:• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to
• Do not use the power cable to drag the device.
Allow the device to cool down sufficiently.• Storage
Before storing the device, observe the following:• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down sufficiently.
• When the device is not being used, observe the following
storage conditions:• Store the device in a dry location and protected from frost
and heat.Store the device in an upright position where it is protected
from dust and direct sunlight. If required, use a cover to protect the device from invasive dust.Place no further devices or objects on top of the device to
prevent it from being damaged.•
Assembly and start-up
Scope of delivery
1 x Device• 2 x Foot
• 4 x Fastening screw
• 1 x Manual
• Unpacking the device
• Open the cardboard box and take the device out.
• Completely remove the packaging.
• Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
The device is not suitable for wall mounting.
Mounting the feet
Mount the feet before positioning the device.• Place the device on its side.
• Fasten each foot with two screws.
Start-up
Info
Odours may occur upon initial start-up or after a longer
period of non-use.
When positioning the device, observe the minimum distancefrom walls or other objects as described in the chapter
Technical annex.• Before starting the device, check the condition of the
power cable. If there are doubts as to their sound condition, contact the customer service. Set the device up in an upright and stable position.• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.• Make sure that extension cables are completely unrolled.
• Make sure that no curtains or other objects interfere with
• the air flow.
Install and set up the device so that it is not positioned
directly below or in front of a wall socket.Ensure that the device is protected from moisture and
water and cannot come into contact with them.
Connecting the power cable
• Connect the mains plug to a properly secured socket.
Route the power cable behind the device. Make sure that the power cable is never routed in front of the device!
ABCCD
Operation
Operating elements
TCH 18 E / TCH 19 E
No.
Designation
flip switch heating levels W
(together with flip switch 9 = W)
flip switch heating levels 750 W
(together with flip switch 8 = W)Rotary switch room thermostat
Switching the device on
• Plug the device into a sufficiently fused socket.
• Set the flip switch (8, 9) to On to select the desired heating
capacity. You can actuate one flip switch for a capacity of 750 W (9) or W (8), or both flip switches for the maximum capacity of W.The lamp at the respective flip switch only lights up
when the room thermostat is switched on.
Setting the room thermostat
• Select the desired temperature via the infinitely variable
rotary switch (10) of the room thermostat. If the room thermostat is switched on, the lamps of the
activated heating levels will light up.The room thermostat controls the room temperature
automatically:• When the set value is exceeded, the heating switches off.
• When the set value is fallen below, the heating
automatically switches back on.
Shutdown
• Do not touch the mains plug with wet or damp hands.
Set both flip switches to Off. Turn the room thermostat's infinitely variable rotary switch (10) counter-clockwise to position MIN. The lamps at the flip switches turn off.• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down completely. If required, clean the device according to the "Maintenance" chapter.Store the device according to the Transport and storage
chapter.• Errors and faults
Tasks which require the device to be opened must only
be carried out by authorised specialist companies or by
the manufacturer.
Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start:• Check the power connection.
Check the power cable and mains plug for damage. If you notice damages, do not try to take the device back into operation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Check the on-site fusing. Check the room temperature. The room thermostat may have switched off, because the desired room temperature has been reached. The room thermostat might be defective. Have a defectiveroom thermostat replaced by a specialist electrical
company. Check whether the overheating protection has tripped (see chapter Safety).• The air current is reduced:
• Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe theminimum distance from walls or other objects according to
the technical data.
The device still does not operate correctly after these
checks: Please contact the customer service. If necessary, bring thedevice to an authorised specialist electrical company or to the
manufacturer for repair.
Technical annex
Technical data
Parameter
Model
Heating capacity
Value
level 1: level 2: level 3:
W W
– 240 V
~50 – 60 Hz
220 – 240 V
~50 – 60 Hz
Maintenance
Activities required before starting maintenance
Do not touch the mains plug with wet or damp hands.
Switch the device off.• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down completely.
• Power supply
Max. powerconsumption
Nominal current
consumption
Fusing
Type of protection
Plug type
Cable length
8.7 A
10 A
IP20
Schuko plug
CEE 7/7
1.2 m
Tasks which require the device to be opened must only
be carried out by authorised specialist companies or by
the manufacturer.
Dimensions
(depth x width x height)
Minimum distance to
walls and other objects
Cleaning the housing
Never immerse the device in water!
Clean the housing with a soft, slightly damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth. Wipe the housing dry after cleaning.
top (A): rear (B): sides (C): front (D):
100 cm
Weight
2.0 kg
8.7 A
10 A
IP20
Schuko plug
CEE 7/7
1.2 m
100 cm
1.5 kg
Information requirements for electrical local space heaters
Parameter
Model
Heat output
Nominal heat output Pnom
Minimum heat output (indicative) Pmin Maximum continuous heat output Pmax,cPower consumption
In the Off state P0
In standby mode Psm
In idle condition Pidle
In networked standby operation Pnsm
Standby operation with information or status indication
Room heating annual efficiency in active operation ηs,an Type of heat output / room temperature controller
Single-stage heat output, no room temperature control
Two or more manual stages, no room temperature control
Room temperature controller with mechanic thermostat
With electronic room temperature controller
Electronic room temperature controller with time of day control
Electronic room temperature controller with weekday control
Other control options
Room temperature controller with presence detection
Room temperature controller with open window detection
Remote control options
Adaptive control of heating start
Operating time limitation
Black bulb sensor
Self-learning function
Control accuracy
Contact details
Value / item
1.8 – 2.0 kW
0.75 kW
2 kW
0.75 kW
2 kW
85.0 %
YES
Disposal
Always dispose of packing materials in an environmentally
friendly manner and in accordance with the applicable local
disposal regulations.
BETRIEBSANLEITUNG
HEIZSTRAHLER
INSTRUCTIONS
CONVECTOR
EN This product is only suitable for well
insulated spaces or occasional use.
Table of contents
You can download the current version of these instructions via
the following link:
Information on the use of these instructions
Safety
Information about the device
Transport and storage
Assembly and start-up
Operation
Errors and faults
https://hub.trotec.com/?id=42756
Maintenance
Technical annex
Disposal
Information on the use of these instructions
Safety
https://hub.trotec.com/?id=42757
Symbols
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or moderate injury.
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity of the device or its site of use.
Read all safety warnings and all instructions.Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.Save all warnings and instructions for future
reference.This appliance can be used by children aged from
8 years and above and persons with reduced physical,sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance. Cleaning anduser maintenance shall not be done by children without
supervision.
Children of less than 3 years should be kept away from the device unless continuously supervised. Children aged from 3 years and less than 8 years shallonly switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance orperform user maintenance
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in an aggressive atmosphere.
• Place the device in an upright and stable position on a
horizontal and stable surface. Let the device dry out after a wet clean. Do not operate it when wet.• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover the device during operation.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible condition.
• Do not sit on the device.
• This appliance is not a toy. Keep away from children and
animals.Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any defective devices or device parts.Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Neveruse the device if electric cables or the power connection
are damaged!The mains connection must correspond to the
specifications in the Technical annex. Insert the mains plug into a properly fused mains socket.• Observe the device's power input, cable length and
• intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical overload. Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by aspecial cord or assembly available from the manufacturer
or its service agent. Defective power cables pose a serious health risk!The power cable must not rest on the device or run in front
of the air outlet, otherwise it may be damaged as a result of high temperatures.• When installing the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions according to the technical
data (chapter Technical annex).
• Do not mount the device to a wall and operate it there.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that the suction side is kept free of dirt and
loose objects.
• Do not place the device on combustible ground.
• Only use original spare parts, for otherwise safe and
• functional operation cannot be ensured.
Allow the device to cool down before transport and/or
maintenance work.The device must not be positioned directly beneath a wall
socket.The device must be set up in a way that the switches and
controllers cannot be touched by a person in a bathtub or
shower.
• Do not use the device if it has been dropped or if it shows
• visible signs of damage.
Keep the safety distance specified in the technical data
between the air inlet and the air outlet of the device and all
combustible materials such as textiles, curtains, beds and sofas, but at least 1 m.
Intended use
The device is only suitable for well insulated spaces or
occasional use. The device is suitable for heating in closed rooms. It has beenspecially developed for private use and is not intended for
commercial use. It is particularly practical to provide additional heating. The device is designed exclusively for installation on the floor. Any use other than the intended use is regarded as misuse.
Reasonably foreseeable misuse
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
• Do not use outdoors.
• Do not use the device for heating vehicles.
• Never immerse the device in water.
• The device must not be mounted to and operated on a
wall.
• Do not make any unauthorised modifications, alterations or
structural changes to the device.
• Do not use the heating device in immediate vicinity of
swimming pools, bathtubs and showers.
Personnel qualification
People who use this device must:• be aware of the dangers that occur when working with
electric devices in damp areas. have read and understood the instructions, especially the Safety chapter.
• Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
the manufacturer.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates that it
is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device. In order to avoid overheating and fire hazards, the heater must not be covered.
Residual risks
Work on the electrical components must only be
carried out by an authorised specialist company!
Before any work on the device, remove the mains plug from the mains socket! Do not touch the mains plug with wet or damp hands.Hold onto the mains plug while pulling the power cable
out of the mains socket.
Risk of electric shock! The device is not protected against water. There is a risk of electric shock! Never use the device in areas where dripping, spraying or running water can enter the device! Never immerse the device in water!
Warning of hot surface
Parts of this appliance can become very hot and cause
burns. Particular attention is to be paid when there are children or vulnerable persons present!
Improper handling entails a risk of burning and electric
shock. Only use the device as intended!
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way! Observe the personnel qualifications!
The device is not a toy and does not belong in the
hands of children.
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Improper installation entails a risk of fire. Do not place the device on combustible ground. Do not place the device on high-pile carpets.
In order to avoid overheating and fire hazards, the device must not be covered!
Behaviour in the event of an emergency
• Switch the device off.
• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to
• Do not reconnect a defective device to the mains.
Overheating protection
The device is provided with a safety thermostat which is
activated by overheating of the device:• In such an event the device switches off automatically.
The lamps at the flip switches for the power stages turn
off.
When the safety thermostat is activated, allow the device to cool down. Only then start to look for the cause of overheating. Should the problem persist, please contact the customer service.
Information about the device
Device description
The convectors TCH 18 E / TCH 19 E serve to generate warm air in interior spaces.The device generates heat by means of an electric heating
element. The air surrounding the heating element is heated. The heated air rises through the air outlet and thus enters the room.The device is equipped with an integrated thermostat and so
generates a constant flow of warm air. The device is not protected against water (IP20)
Device depiction
No. Designation
Air outlet
Control panel
Foot
Carrying handle
Air inlet
Transport and storage
If you store or transport the device improperly, the device may be damaged.Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry handle.
Switch the device off.
Before transporting the device, observe the following:• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to
• Do not use the power cable to drag the device.
Allow the device to cool down sufficiently.• Storage
Before storing the device, observe the following:• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down sufficiently.
• When the device is not being used, observe the following
storage conditions:• Store the device in a dry location and protected from frost
and heat.Store the device in an upright position where it is protected
from dust and direct sunlight. If required, use a cover to protect the device from invasive dust.Place no further devices or objects on top of the device to
prevent it from being damaged.•
Assembly and start-up
Scope of delivery
1 x Device• 2 x Foot
• 4 x Fastening screw
• 1 x Manual
• Unpacking the device
• Open the cardboard box and take the device out.
• Completely remove the packaging.
• Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
The device is not suitable for wall mounting.
Mounting the feet
Mount the feet before positioning the device.• Place the device on its side.
• Fasten each foot with two screws.
Start-up
Info
Odours may occur upon initial start-up or after a longer
period of non-use.
When positioning the device, observe the minimum distancefrom walls or other objects as described in the chapter
Technical annex.• Before starting the device, check the condition of the
power cable. If there are doubts as to their sound condition, contact the customer service. Set the device up in an upright and stable position.• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.• Make sure that extension cables are completely unrolled.
• Make sure that no curtains or other objects interfere with
• the air flow.
Install and set up the device so that it is not positioned
directly below or in front of a wall socket.Ensure that the device is protected from moisture and
water and cannot come into contact with them.
Connecting the power cable
• Connect the mains plug to a properly secured socket.
Route the power cable behind the device. Make sure that the power cable is never routed in front of the device!
ABCCD
Operation
Operating elements
TCH 18 E / TCH 19 E
No.
Designation
flip switch heating levels W
(together with flip switch 9 = W)
flip switch heating levels 750 W
(together with flip switch 8 = W)Rotary switch room thermostat
Switching the device on
• Plug the device into a sufficiently fused socket.
• Set the flip switch (8, 9) to On to select the desired heating
capacity. You can actuate one flip switch for a capacity of 750 W (9) or W (8), or both flip switches for the maximum capacity of W.The lamp at the respective flip switch only lights up
when the room thermostat is switched on.
Setting the room thermostat
• Select the desired temperature via the infinitely variable
rotary switch (10) of the room thermostat. If the room thermostat is switched on, the lamps of the
activated heating levels will light up.The room thermostat controls the room temperature
automatically:• When the set value is exceeded, the heating switches off.
• When the set value is fallen below, the heating
automatically switches back on.
Shutdown
• Do not touch the mains plug with wet or damp hands.
Set both flip switches to Off. Turn the room thermostat's infinitely variable rotary switch (10) counter-clockwise to position MIN. The lamps at the flip switches turn off.• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down completely. If required, clean the device according to the "Maintenance" chapter.Store the device according to the Transport and storage
chapter.• Errors and faults
Tasks which require the device to be opened must only
be carried out by authorised specialist companies or by
the manufacturer.
Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start:• Check the power connection.
Check the power cable and mains plug for damage. If you notice damages, do not try to take the device back into operation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Check the on-site fusing. Check the room temperature. The room thermostat may have switched off, because the desired room temperature has been reached. The room thermostat might be defective. Have a defectiveroom thermostat replaced by a specialist electrical
company. Check whether the overheating protection has tripped (see chapter Safety).• The air current is reduced:
• Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe theminimum distance from walls or other objects according to
the technical data.
The device still does not operate correctly after these
checks: Please contact the customer service. If necessary, bring thedevice to an authorised specialist electrical company or to the
manufacturer for repair.
Technical annex
Technical data
Parameter
Model
Heating capacity
Value
level 1: level 2: level 3:
W W
– 240 V
~50 – 60 Hz
220 – 240 V
~50 – 60 Hz
Maintenance
Activities required before starting maintenance
Do not touch the mains plug with wet or damp hands.
Switch the device off.• Disconnect the device from the mains by removing the
mains plug from the socket. When doing so, be sure to Allow the device to cool down completely.
• Power supply
Max. powerconsumption
Nominal current
consumption
Fusing
Type of protection
Plug type
Cable length
8.7 A
10 A
IP20
Schuko plug
CEE 7/7
1.2 m
Tasks which require the device to be opened must only
be carried out by authorised specialist companies or by
the manufacturer.
Dimensions
(depth x width x height)
Minimum distance to
walls and other objects
Cleaning the housing
Never immerse the device in water!
Clean the housing with a soft, slightly damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth. Wipe the housing dry after cleaning.
top (A): rear (B): sides (C): front (D):
100 cm
Weight
2.0 kg
8.7 A
10 A
IP20
Schuko plug
CEE 7/7
1.2 m
100 cm
1.5 kg
Information requirements for electrical local space heaters
Parameter
Model
Heat output
Nominal heat output Pnom
Minimum heat output (indicative) Pmin Maximum continuous heat output Pmax,cPower consumption
In the Off state P0
In standby mode Psm
In idle condition Pidle
In networked standby operation Pnsm
Standby operation with information or status indication
Room heating annual efficiency in active operation ηs,an Type of heat output / room temperature controller
Single-stage heat output, no room temperature control
Two or more manual stages, no room temperature control
Room temperature controller with mechanic thermostat
With electronic room temperature controller
Electronic room temperature controller with time of day control
Electronic room temperature controller with weekday control
Other control options
Room temperature controller with presence detection
Room temperature controller with open window detection
Remote control options
Adaptive control of heating start
Operating time limitation
Black bulb sensor
Self-learning function
Control accuracy
Contact details
Value / item
1.8 – 2.0 kW
0.75 kW
2 kW
0.75 kW
2 kW
85.0 %
YES
Disposal
Always dispose of packing materials in an environmentally
friendly manner and in accordance with the applicable local
disposal regulations.